原标题："上传并安装SSL-V\/P\/N\/-Client到路由器【图文】"关于路由器的知识分享。 - 素材来源网络 编辑:kaka。
在本实验中，为了使路由器支持sslV\/P\/N\/需要上传并安装SSL-V\/P\/N\/-Client到路由器。由此为前提来模拟sslV\/P\/N\/的安全技术。sslV\/P\/N\/配置下节实验做介绍。
在上传安装ssl-V\/P\/N\/-client之前，先搭建tftp服务器，本次试验用的是cisco tftp server 1.1。测试路由器和tftp server的连通性R1#ping 192.168.1.2Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 8/17/36 msR1#路由器和tftp服务器成功通信，下面我来上传ssl-V\/P\/N\/-client
- 释放disk0空间用作存储上传文件R1#format disk0:Format operation may take a while. Continue? [confirm]Format operation will destroy all data in "disk0:". Continue? [confirm]Format: Drive communication & 1st Sector Write OK...Writing Monlib sectors......................................................................................................................................................Monlib write completeFormat: All system sectors written. OK... Format: Total sectors in formatted partition: 130883 Format: Total bytes in formatted partition: 67012096Format: Operation completed successfully. Format of disk0 comple
- 上传ssl-V\/P\/N\/-client R1#copy tftp: disk0: Address or name of remote host []? 192.168.1.2 Source filename []? sslclient.pkg Destination filename [sslclient.pkg]? Accessing tftp://192.168.1.2/sslclient.pkg... Loading sslclient.pkg from 192.168.1.2 (via FastEthernet1/0): !!!!!!!!! [OK - 2208871 bytes] 2208871 bytes copied in 56.880 secs (38834 bytes/sec)
- 安装ssl-V\/P\/N\/-client R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#webV\/P\/N\/install svc disk0:/sslclient.pkg SSLV\/P\/N\/Package SSL-V\/P\/N\/-Client : installed successfully R1(config)#成功上传并安装了ssl-V\/P\/N\/-client，这台路由器支持sslV\/P\/N\/了。
本文出自 “阅微草堂笔记” 博客，请务必保留此出处http://loverain.blog.51cto.com/2271638/824709
以上就是关于“上传并安装SSL-V\/P\/N\/-Client到路由器【图文】”的教程，由路由器指南网整理
本文来自投稿，不代表路由百科立场，如若转载，请注明出处：https://www.qh4321.com/172601.html
- 安装ssl-V\/P\/N\/-client R1#conf t Enter configuration commands, one per line. End with CNTL/Z. R1(config)#webV\/P\/N\/install svc disk0:/sslclient.pkg SSLV\/P\/N\/Package SSL-V\/P\/N\/-Client : installed successfully R1(config)#成功上传并安装了ssl-V\/P\/N\/-client，这台路由器支持sslV\/P\/N\/了。
- 上传ssl-V\/P\/N\/-client R1#copy tftp: disk0: Address or name of remote host []? 192.168.1.2 Source filename []? sslclient.pkg Destination filename [sslclient.pkg]? Accessing tftp://192.168.1.2/sslclient.pkg... Loading sslclient.pkg from 192.168.1.2 (via FastEthernet1/0): !!!!!!!!! [OK - 2208871 bytes] 2208871 bytes copied in 56.880 secs (38834 bytes/sec)
